VandalStop Installation and Troubleshooting Manual

Prefer a PDF? Download the complete installation and troubleshooting manual (Spanish).

⬇ Download PDF manual

Quick summary: VandalStop is an anti-vandalism alarm system for vending machines. It detects knocks and impacts using sensors, plays a deterrent warning on the spot and sends notifications through a mobile app (WiFi or GSM). It reduces vandalism incidents by up to 90%. The service works on a SaaS model: an initial payment (includes hardware + first year of service) and an annual maintenance fee of €100 + VAT/year from the second year onwards, covering detection, warnings, notifications and technical support (2026 price, subject to review).

Kit components

  • VS control unit: control unit with 3 buttons (volume, pairing) and a QR code to download the app.
  • Power supply, 12V 2A (other voltages or currents may damage the device).
  • Impact sensors: with rear magnets or adhesive tape to attach them to any surface of the machine.
  • Ceiling speaker: so the deterrent warning can be heard clearly in the store.
  • Connection cables for the impact sensors and speaker.

Installing the impact sensors

  1. Choose the installation position: a clean, even surface.
  2. Remove the sensor cover by unscrewing the captive screw.
  3. Carefully lift the printed circuit board off the base.
  4. Mark and fix the base in the mounting position.
  5. Feed the cables through the rear or side entry, depending on the mounting chosen.
  6. Connect the cables to the sensor: white = negative, red = positive, green and yellow = signal.
  7. Adjust the sensitivity by turning the potentiometer until the sensor responds only to the desired impact.
  8. Refit the cover and check the response to an impact.

Important: always handle the sensors and connect the cables with the control unit disconnected from the power supply.

Impact sensor technical data

Supply voltage 9V to 16V DC
Standby current 15mA maximum
Temperature range -20°C to +60°C
Pulse count 2, 4 or 6 (configurable)
Dimensions 25 x 23 x 85 mm

Full kit installation

  1. Place the sensors inside the machine or on the door glass and connect the cables.
  2. Place the speaker outside the store so it can be heard clearly.
  3. Connect the sensors and speaker to the control unit. All 4 slots must be occupied by sensors or jumpers.
  4. Connect the control unit to the power supply (never with sensors disconnected at that moment).

Start-up and app connection

  1. Download the app by scanning the QR code on the control unit.
  2. Create an account with your email address and verify it.
  3. Tap add device and then press the pairing button.
  4. Connect your phone’s WiFi to the VANDALSTOP local network (password: Vandalstop).
  5. Choose the connection mode: WiFi or GSM.
  6. Select the audio mode (Voice, Siren or Silent) and adjust the volume.

LED status

  • Red LED on: sensor triggered, slot without a sensor/jumper, or sensor incorrectly connected.
  • Solid green LED: connected correctly.
  • Slow-flashing green LED: waiting to be paired.
  • Fast-flashing green LED: unable to connect (repeat pairing).
  • Blue LED: should be off except during pairing.

Troubleshooting guide

Power and start-up

Issue Check Solution
The device does not switch on Check the power LED next to the power port Replace the power supply; if the problem persists, send the control unit to technical service
Random restarts Check that the power supply is the original one (12V 2A) Replace it with the official power supply and check the mains connections

Sensor issues

Issue Check Solution
A sensor stops working Check the connector and cable; swap the port with a working sensor If the fault follows the port, it is the control unit; if it follows the sensor, replace the sensor or cable
Loss of sensitivity Adjust the sensor potentiometer Adjust the sensitivity; if it does not respond, replace the sensor
Random detection (false alarms) Check whether the cable is loose or near a source of interference Secure the cable; if it continues, replace the sensor
Door opening not detected Check the distance between the magnetic sensor and the magnet Reposition the magnet within 2 cm of the sensor

Audio and alarms

Issue Check Solution
No sound (detects but does not sound) Check the audio port and cable; check whether silent mode is on Turn up the volume on the unit and check the speaker connection
Distorted sound Check for moisture in the speaker or a damaged cable Replace the speaker or the audio cable

Control unit and notifications

Issue Check Solution
Notifications not arriving Check the green LED (solid = OK, flashing = no connection) Restart the router and check coverage at the machine’s location
Pairing failure Press Pairing Mode and check the corresponding LED Move the phone closer to the device and restart the app

Appendix: door sensor (magnetic contact)

This sensor protects doors, windows or surfaces against attempts to open them or heavy blows, with two sensitivity levels.

  • Green LED: correct detection.
  • Red LED: sensitivity too low.
  • Orange LED: sensitivity too high (risk of false alarms).

Level selector: High for fragile doors or windows, Low for solid doors. The magnet must be placed within 2 cm of the sensor.

Spare parts and component prices (RRP, excl. VAT)

Component Price
8-port control unit (without power supply) €250.00
Power supply (12V 2A) €14.00
VandalStop speaker €35.00
Machine sensor + 5m cable (standard kit) €45.00
Machine sensor (sensor only) €40.00
Door sensor + 5m cable (magnetic) €65.00
Door sensor (sensor only) €55.00
Sensor cable (connector included) €2.00 per metre
Audio cable (connector included) €2.50 per metre

Shipping costs not included. Prices subject to review.

Service terms (SaaS model)

When purchasing the VandalStop device, the customer makes a single initial payment that includes the hardware and the service subscription for the first year (impact detection, deterrent warnings and notifications).

From the second year onwards, continued service requires an annual renewal of €100 + VAT (2026 price). This fee keeps impact detection, deterrent warnings, notifications and technical support active. If it is not renewed, the hardware remains the customer’s property, but its functions stop working until the subscription is reactivated.

Warranties

  • VandalStop control unit: 2-year legal warranty against manufacturing defects.
  • Sensors (impact and door): 1-year limited warranty.
  • Accessories and cables: dead-on-arrival warranty (immediate replacement if they fail on first installation).

Right of withdrawal

14 calendar days from receipt of the product, unless the hardware has already been physically installed or paired with the app.

Technical support

  • Remote support: chat or email (support@vandalstop.es).
  • Video call support: by appointment, for complex sensor or network diagnostics.

Download the complete PDF manual (Spanish)

Agenda una demo

Agenda una demo y te mostraremos el funcionamiento




This will close in 0 seconds